In the Completing the Add Hardware Wizard dialog box, click Finish, and then click OK.On the Windows server side we will have the IP address 3.3.3.1/30 and the interface on the NB2 connecting to the AAA server will have the IP address 3.3.3. If a message about driver signing appears, click Continue Anyway. The NBtoACS adapter will be used to connect the GNS3 world to VMware world, so that the NB2 router can talk to the AAA server, or any other router can talk to the AAA server through NB2.In the Network Adapter list, click Microsoft Loopback Adapter, and then click Next twice.In the Manufacturer list, click Microsoft.In the Common hardware types list, click Network adapters, and then click Next.In the What do you want the wizard to do? list, click Install the hardware that I manually select from a list (Advanced), and then click Next.In the Installed hardware list, click Add a new hardware device, and then click Next. This article helps fix an issue where you cant find the Microsoft Loopback Adapter.When the Is the hardware connected? dialog box appears, click Yes, I have already connected the hardware, and then click Next.In the Add Hardware dialog box, click Next.In the System Properties dialog box, on the Hardware tab, click Add Hardware Wizard. Edited Februat 2:36 AM GNS3 with MS-Loopback issue Good Day Everyone.Depending on the style of the start menu, My Computer may be located in the Start menu. In the host operating system, right-click My Computer, and then select Properties.Without the always keyword, R1 will only advertise a default route if it already has a default route in its routing table, but adding the keyword means that R1 will advertise a default route, even if it does not have a default route in its routing table.For step 9 the Network Adapter list, cannot find Microsoft Loopback Adapter. You could make sure that R1 always advertises a default route: router ospf 1ĭefault-information originate always ! add the always keyword You could add a default route to the R1 routing table: ip route 0.0.0.0 0.0.0.0 Loopback0 202.78.10.10 I am routing all of the directly connected subnets through the use of eigrp and all 3 routers can talk to each other. (which is using MS Loopback adapter on Windows 8). This would also work only if you already have a default route in your routing table. I have an image for all of the devices that can be supported on gns3, Im working on ccna security 640-554. I see that you have the default-information originate statement as well. The network statements under router ospf do not include the loopback interface. Network 202.78.10.10 0.0.0.0 area 0 ! add this line The loopback interface in R1 is not in the OSPF domain. You can add the R1 Loopback address to the R1 OSPF: router ospf 1 I tried to see if the WinPcap compatibility troubleshooter helps. That means R3 has no idea how to reach the R1 Loopbak0 address, so it drops packets destined to that address. ASA(inside)>ethernet switch>Cloud(loopback adapter) ASA(inside) - 10.10.10.1/24 Loopback Adapter - 10.10.10.2/24 But I am still not able to ping from ASA (inside) to Loopback Adapter or vice-versa. Your R1 Loopback0 interface has this address: ip address 202.78.10.10 255.255.255.255īut you are not advertising that address in the R1 OSPF: router ospf 1 Ip nat inside source list 1 interface GigabitEthernet5/0 overloadĪccess-list 1 permit 192.168.50.0 0.0.0.31 Mgcp behavior comedia-check-media-src disable Username - secret 5 $1$D/vk$a8XNtzs/Cir2tVb/H7Lxv0 R1 configuration are shown below hostname R1 Under Windows machine, I used Microsoft Loopback Adapter (Install Microsoft Loopback Adapter) to share my Physical Adapters (Ethernet or Wi-Fi) Internet with my GNS3 topology or to access GNS3 topology devices from Windows Host. I'm unable to ping R1 loopback interface (destination host unreachable)
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |